Instrumentation in Tractor for Evaluating Performance of a Tractor Drawn Rotavator
DOI:
https://doi.org/10.52151/jae2024614.1858Keywords:
power take-off (PTO) torque, rotavator, sensors, specific energy requirement, throttle settings, wheel slipAbstract
Performance measurement of agricultural machinery is essential for enhancing their efficiency for which they are operated. The performance related data helps the operator to select optimum operating parameters which reduce fuel consumption and increase field productivity. This study was aimed to develop various sensing units and install them on the tractor for evaluating performance of a tractor drawn rotavator. A microcontroller based embedded system was developed for continuous recording of wheel slip, actual forward speed, throttle opening, engine speed, velocity ratio, draft and power take-off (PTO) torque related data while carrying out tillage operation with rotavator. The wheel slip (from 1.5% to 35%) and actual forward speed of the tractor (up to 6 km h-1) was measured using inductive proximity sensors. For measuring throttle opening (0 to 100%), engine speed (750 to 2500 rpm), draft (65 to 350 kg) and PTO torque (up to 420 N-m) values, a potentiometer, magnetic pickup sensor, S-type loadcell and PTO torque transducer, respectively, were used. For computing velocity ratio, peripheral speed of rotavator was measured using PTO speed data received from PTO torque transducer, and actual forward speed of tractor was measured using inductive proximity sensor. The developed sensing units were calibrated under both dynamic and static conditions, and were also verified in laboratory and field conditions. Results showed that output signals received from the sensing units varied linearly with applied load. The mean absolute percentage error (MAPE) between measured and actual values was found to be below 5%. From the measured parameters, specific energy requirement and total power required for carrying out tillage operation could be computed. The power requirement was found to increase with increase in both gear and throttle settings. The specific energy requirement was minimum when rotavator was operated in L2 gear of the tractor. The minimum specific energy of 21 Wh m-3 was found at L2 gear and 75% throttle opening.
Downloads
References
ASABE. (2006). ASAE D497.5. Agricultural Machinery Management Data. American Society of Agricultural and Biological Engineers, Joseph, St. Michigan, USA.
Behera, A., & Raheman H. (2020). Effect of peripheral to forward speed ratio on overall performance an active tillage implement: Tractor drawn rotavator. Journal of the Institution of Engineers (India): Series A, 102, 981-988. https://10.1007/s40030-021-00567-4
Bentaher, H., Hamza E., Kantchev, G., Maalej, A., & Arnold, W. (2008). Three-point hitch mechanism instrumentation for tillage power optimization. Biosystems Engineering, 100, 24-30. https://doi.org/10.1016/j.biosystemseng.2008.01.008
Bhambota, S., Singh, M. S., Prakash, A., & Dixit, A. (2017). Effect of blade shape and rotor speed of rotavator of on pulverization and mixing quality of soil. Agricultural Engineering Today, 38(4), 25-30. https://10.5958/2395-146X.2017.00072.2
Chen, J., Dai, J. H., Pan, C. G., & Gao, L. (1993). Studies on the down-cut energy-saving rotary blades. Transactions of the Chinese Society of Agricultural Machinery, 24(1), 37-42.
Grisso, R. D., & Pitman, R. (2001). Gear up and throttle down −saving fuel. Publication-442-450 (BSE-326P). Virginia Cooperative Extension, Virginial Tech., Virginia State University, USA. Available at: https://www.pubs.ext.vt.edu/content/dam/pubs_ext_vt_edu/442/442-450/BSE-326.pdf (Accessed on: 19 Aug 2024).
Grisso, R. D., Kocher, M. F., & Vaughan, D. H. (2004). Predicting tractor fuel consumption. Applied Engineering in Agriculture, 20(5), 553‐561. https://doi.org/10.13031/2013.17455
Hendrick, J. G. (1980). A powered rotary chisel. Transaction of American Society of Agricultural Engineering, 23(6), 1349-1352. https://doi.org/10.13031/2013.34777
Hensh, S., Tewari, V. K., & Upadhyay, G. (2021). A novel wireless instrumentation system for measurement of PTO (power take-off) torque requirement during rotary tillage. Biosystems Engineering, 212, 241-251. https://doi.org/10.1016/j.biosystemseng.2021.10.015
Keskin, M., Sekerli, Y. E., & Kahraman, S. (2017). Performance of two low-cost GPS receivers for ground speed measurement under varying speed conditions. Precision Agriculture, 18, 264-277. https://doi.org/10.1007/s11119-016-9453-x
Kumar, A. A., Tewari, V. K., & Nare, B. (2017). Embedded digital draft force and wheel slip indicator for tillage research. Computers and Electronics in Agriculture, 127, 38–49. https://doi.org/10.1016/j.compag.2016.05.010
Kumari, A., & Raheman, H. (2023a). Tillage operation with a tractor drawn rotavator using an embedded advisory system for minimizing fuel consumption. Journal of Biosystems Engineering, 48(4), 487-502. https://doi.org/10.1007/s42853-023-00207-8
Kumari, A., & Raheman, H. (2023b). Effect of throttle position and gear selection on specific energy requirement and power utilization efficiency of a tractor drawn rotavator in sandy clay loam soil. Journal of the Institution of Engineers (India): Series A, 104(4), 819-829. https://doi.org/10.1007/s40030-023-00765-2
Lee, J. W., Kim, J. S., & Kim, K. U. (2016). Computer simulations to maximize fuel efficiency and work performance of agricultural tractors in rotovating and ploughing operations. Biosystems Engineering, 142, 1-11. https://doi.org/10.1016/j.biosystemseng.2015.11.012
Mandal, S. K., Bhattacharyya, B., Mukherjee, S., & Prasad, A. K. (2016). Design optimization of rotary tiller blade using specific energy requirement. International Journal of Current Engineering and Technology, 6(4), 1257-1263. https://doi.org/10.14741/Ijcet/22774106/6.4.2015.31
McLaughlin, N. B., Heslop, L. C., Buckley, D. J., St. Amour, G. R., Compton, B. A., Jones, A. M., & Van Bodegom, P. (1993). General purpose tractor instrumentation and data logging system. Transaction of American Society of Agricultural Engineering, 36(2), 265–273. https://doi.org/10.13031/2013.28334
Naik, V. S., & Raheman, H. (2019). Factors affecting fuel consumption of tractor operating active tillage implement and its prediction. Engineering in Agriculture, Environment and Food, 12, 548-555. https://doi.org/10.1016/j.eaef.2019.11.007
O'Dogherty, M. J. (1996). The design of octagonal ring dynamometer. Journal of Agricultural Engineering Research, 63, 9-18. https://doi.org/10.1006/jaer.1996.0002
Pranav, P. K., Pandey, K. P., & Tewari, V. K. (2010). Digital wheel slipmeter for agricultural 2WD tractors. Computers and Electronics in Agriculture, 73(2), 188-193. https://doi.org/10.1016/j.compag.2010.05.003
Pranav, P. K., Pandey, K. P., & Tewari, V. K. (2015). Development of electronic ground speed sensor for tractors. Journal of Agricultural Engineering, 52(3), 46-50. https://doi.org/10.52151/jae2015523.1583
Raheman, H., & Jha, S. K. (2007). Wheel slip measurement in 2WD tractor. Journal of Terramechanics, 44(1), 89-94. https://doi.org/10.1016/j.jterra.2006.03.001
Saimbhi, V. S., Wadhwa, D. S., & Grewal, P. S. (2004). Development of a rotary tiller blade using three-dimensional computer graphics. Biosystems Engineering, 89(1), 47-58. https://doi.org/10.1016/j.biosystemseng.2004.05.011
Shinners, K. J., Wilkes, J. M., & England, T. D. (1993). Performance characteristics of tillage machine with active‐passive components. Journal of Agricultural Engineering Research, 55, 277-297. https://doi.org/10.1006/jaer.1993.1050
Shrivastava, P., Tewari, V. K., Gupta, C., & Chouriya, A. (2023). HMI-assisted visual interface-cum-embedded system for measurement of tractor-implement performance parameters. Journal of Field Robotics, 1-22. https://doi.org/10.1002/rob.22221
Thakur, T. C., & Godwin, R. J. (1988). Design of extended octagonal ring dynamometer for rotary studies. Agricultural Mechanization in Asia, Africa and Latin America, 19(3), 23-28.
Upadhyay, G., & Raheman, H. (2020a). Effect of velocity ratio on performance characteristics of an active-passive combination tillage implement. Biosystems Engineering, 191, 1-12. https://doi.org/10.1016/j.biosystemseng.2019.12.010
Upadhyay, G., & Raheman, H. (2020b). Comparative assessment of energy requirement and tillage effectiveness of combined (active-passive) and conventional offset disc harrow. Biosystems Engineering, 198, 266-279. https://doi.org/10.1016/j.biosystemseng.2020.08.014
Upadhyay, G., Raheman, H., & Dubey, R. (2022). Novel draught resistance sensing elements for measurement of drawbar power of agricultural machinery. Spanish Journal of Agricultural Research, 20(4), e0208. https://doi.org/10.5424/sjar/2022204-19171
Usaborisut, P., & Prasertkan, K. (2019). Specific energy requirements and soil pulverization of a combined tillage implement. Heliyon, 5(11), Article e02757. https://doi.org/10.1016/j.heliyon.2019.e02757
Watyotha, C., & Salokhe, V. M. (2001). Development of a data acquisition system for measuring the characteristics of real time forces by cage wheels. Journal of Terramechanics, 38, 201-210. https://doi.org/10.1016/S0022-4898(00)00021-5
Yadav, R., & Raheman, H. (2023). Development of an artificial neural network model with graphical user interface for predicting contact area of bias-ply tractor tyres on firm surface. Journal of Terramechanics, 107, 1-11. https://doi.org/10.1016/j.jterra.2023.01.004
Zhixiong, L., Xuefeng, B., Yiguan, L., Jiangxue, C., & Yang, L. (2013). Wheel slip measurement in 4WD tractor based on LABVIEW. International Journal of Automation and Control Engineering, 2(3), 113-119.
