Evaluation of a Power Tiller Operated De-Topper-cum-Digger for Onion Crop Harvesting
DOI:
https://doi.org/10.52151/jae2025624.1975Keywords:
de-topping efficiency, digging efficiency, onion damage, onion harvesting, smallholder mechanizationAbstract
To enhance mechanization of onion harvesting on small farms and increase the annual utilization of power tillers, a de-topper-cum-digging unit was evaluated for simultaneous removal of onion leaves and digging of topped bulbs using a 9.7 kW power tiller. The field evaluation was conducted at the rake angle of 21° and a digging depth of 70 mm. The height of cut above crown was measured to be 31±7 mm. The absolute cutting torque and total maximum cutting torque for the de-topping unit were measured to be 2.12±0.49 N-m and 2.64±0.49 N-m, respectively at a rotational speed of 1790.95 rpm. The average maximum torque for the conveying unit was observed to vary between 8.46 and 13.21 N-m when operated in first gear with an idle torque of 1.41 N-m as compared to that observed in the range 15.40 to 23.28 N-m with an idle torque of 1.69 N-m when operated in second gear of rotor shaft of the power tiller. The de-topping efficiency, digging efficiency, field efficiency, actual field capacity and damage percentage of onion bulbs were found to be 82%, 92%, 65%, 0.042 ha h-1 and 10%, respectively. The total power requirement for harvesting onion crop (including de-topping, digging, and conveying) was found to be 0.81 kW. The performance assessment indicated satisfactory results, suggesting the viability of the de-topper-cum-digger for use by small landholding farmers cultivating onions.
Downloads
References
Anonymous. (2022). Onion Consumption Per Capita in India. Available at: https://www.helgilibrary.com/indicators/onion-consumption-percapita/india/ (accessed on 20 Aug 2022).
BIS. (1993). IS 13818:1993 Test code, Indian standards on harvesting equipment-Tractor operated potato digger shakers. Bureau of Indian Standards, New Delhi
Dihingia, P. C., Kumar, G. V. P., Singh. L. K., & Saikia, U. S. (2024). Assessment of cost economics of power tiller operated 2-row vegetable transplanter. Indian Journal of Hill Farming, 37(1), 190-198. https://doi.org/10.56678/iahf-2024.37.01.25
El-Fakhrany, W. B. & Fathalla, F. H. (2020) Utilization of the two-wheel tractor in onion digging operation. Journal of Soil Sciences and Agricultural Engineering, 11(11), 609-615. https://doi.org/10.21608/jssae.2020.135648 DOI: https://doi.org/10.21608/jssae.2020.135648
Gavino, H. F., Mateo, W. C., & Devera, C. R. C. (2018). Development of a locally made power tiller driven onion harvester. Paper presented during the 15th International Agricultural and Biosystems Engineering Conference and Exhibition, 29th Philippine Agricultural Engineering Week and 68th PSABE Annual National Convention on April 22-28, 2018 held in University of Southeastern Philippines (USEP) Sports and Cultural Center, Davao City, Philippines.
Hamid, M. A., Ahmad, D., Rukunudin, I. H., Shamsuddin, S., & Yahya, A. (2014). Design and development of a sweet potato digging device. Journal of Science & Technology, 22(1), 43-53.
ICAR–DOGR. (2017). Report of the Quinquennial Review Team on the Directorate of Onion and Garlic Research. ICAR–Directorate of Onion and Garlic Research, Pune, Maharashtra, India. Available at: https://icar.org.in/sites/default/files/2022-07/QRT-DOGR-01.pdf?utm_source (accessed on 20th Aug 2022).
Kadam, D. M., Dongre, R., Gupta, R., Gautam, R., & Rajak, S. K. (2023). Performance evaluation of tractor drawn root crop harvester for harvesting of potato and ginger crop. Biological Forum, 15(3), 564-570.
Kang, W. S., Wright, M., Chung, C. J., & Kim, S. H. (1986). Effects of an oscillating inclined blade on soil break-up and energy requirements (I)-balancing and torque analysis. Journal of Biosystems Engineering, 11(2), 4-13.
Keikha, A., Parashkoohi, M. G., Mohammadi, A., & Afshari, H. (2025). Comparing mechanization systems for regression model based crop production under different tillage systems. Results in Engineering, 25,104056. https://doi.org/10.1016/j.rineng.2025.104056 DOI: https://doi.org/10.1016/j.rineng.2025.104056
Kepner, R. A., Bainer, R., & Barger, E. L. (2005). Principles of Farm Machinery (4th ed.). New Delhi: CBS Publishers.
Khura, T. K., Mani, I., & Srivastava, A. P. (2011). Design and development of tractor-drawn onion (Allium cepa) harvester. Indian Journal of Agricultural Sciences, 81(6), 528-532.
Kumar, S., Kumar, N., Kumar, R., & Pandey, K. P. (2020). An instrumentation system for monitoring field performance of agricultural tractor under ballasting and non-ballasting conditions. Agricultural Engineering Today, 44(2), 32-40. DOI: https://doi.org/10.52151/aet2020442.1519
Kumawat, L. (2023). Development of A Hand Tractor Powered Topper Cum Digger for Onion Crop. Unpublished Doctoral Dissertation. Indian Institute of Technology, Kharagpur.
Kumawat, L., & Raheman, H. (2022a). Mechanization in onion harvesting and its performance: A review and a conceptual design of onion harvester from Indian perspective. Journal of the Institution of Engineers (India): Series A, 103(1), 295-304. https://doi.org/10.1007/s40030-021-00611-3 DOI: https://doi.org/10.1007/s40030-021-00611-3
Kumawat, L., & Raheman, H. (2022b). Laboratory investigations on cutting torque and efficiency for topping of onion leaves using wire-type rotary unit. Journal of Biosystems Engineering, 47(4), 428-438. https://doi.org/10.1007/s42853-022-00156-8 DOI: https://doi.org/10.1007/s42853-022-00156-8
Kumawat, L., & Raheman, H. (2023a). Determination of engineering properties of onion crop required for designing an onion harvester. Cogent Engineering, 10(1), 2191404. https://doi.org/10.1080/23311916.2023.2191404 DOI: https://doi.org/10.1080/23311916.2023.2191404
Kumawat, L., & Raheman, H. (2023b). Development of draft force estimation model for hand tractor powered digger-cum-conveyor by rake angle and digging depth. Journal of Biosystems Engineering, 48(2), 152-164. https://doi.org/10.1007/s42853-023-00179-9 DOI: https://doi.org/10.1007/s42853-023-00179-9
Kumawat, L., Raheman, H., Upadhyay, G., & Somra, A. (2024). Development of a hand tractor powered de-topper cum digger for onion crop. Cogent Engineering, 11(1), 2393231. https://doi.org/10.1080/23311916.2024.2393231 DOI: https://doi.org/10.1080/23311916.2024.2393231
Laryushin, N. P., & Laryushin, A. M. (2009). Energy-saving onion harvesting technology. Russian Agricultural Sciences, 35(1), 66-67. https://doi.org/10.3103/S1068367409010224 DOI: https://doi.org/10.3103/S1068367409010224
Mahajan, V., Thangasamy, A., Bhagat, Y., Benke, A., & Khade, Y. (2017). Scope and challenges in cultivation of onion and garlic through mechanization. In: A. P. Benke, S. S. Gadge, Y. Bhagat, V. Mahajan & M. Singh (Eds), Mechanization in Onion and Garlic Cultivation- Way Forward. Brainstorming on Challenges in Mechanization of Onion and Garlic Production in India (pp. 1–13). ICAR-Directorate of Onion & Garlic Research, Rajgurunagar, Pune.
Mahapatra, J., Kashyap, V., & Sharma, A. K. (2020). A theoretical method for efficient design of power tiller rotavator satisfying multiple objectives. Current Journal of Applied Science and Technology, 39(12), 107-15. https://doi.org/10.9734/cjast/2020/v39i1230668 DOI: https://doi.org/10.9734/cjast/2020/v39i1230668
Maswaure, J. (1995). Tillage Forces and Soil Loosening as Influenced by Tool Geometry. Master’s Thesis, Department of Bioresource Engineering, McGill University, Montreal, Canada.
Maw, B. W., & Mullinix, B. G. (2001) Grade distribution of sweet onions harvested at different maturities. Applied Engineering in Agriculture, 17(6), 833. https://doi.org/10.13031/2013.6828 DOI: https://doi.org/10.13031/2013.6828
Mehta, T. D., & Yadav, R. (2015). Development and Performance Evaluation of Tractor Operated Onion Harvester. Agricultural Mechanization in Asia, Africa, and Latin America, 46(4), 7-13.
Naik, M. A., Pateriya, R. N., & Ramulu, C. (2022). Optimization of performance parameters of onion digger with cutter bar topping unit. Journal of The Institution of Engineers (India): Series A, 103, 71-79. https://doi.org/10.1007/s40030-021-00596-z DOI: https://doi.org/10.1007/s40030-021-00596-z
Naresh, Rani, V., Jain, M., Kumar, A., & Narender. (2018). Design and development of tractor operated carrot digger. Agricultural Mechanization in Asia, Africa and Latin America, 49(3), 79-85.
Nataraj, E., Sarkar, P., Raheman, H., & Upadhyay, G. (2021). Embedded digital display and warning system of velocity ratio and wheel slip for tractor operated active tillage implements. Journal of Terramechanics, 97, 35-43. https://doi.org/10.1016/j.jterra.2021.06.003 DOI: https://doi.org/10.1016/j.jterra.2021.06.003
Nisha, N., & Shridar, B. (2018). Development of power tiller operated harvester for small onion (Allium cepa var. Aggregatum). International Journal of Agricultural Science and Research, 8(1), 73-78. DOI: https://doi.org/10.24247/ijasrfeb201811
Omar, O. A., Abdel Hamid, S. G., & El-Termzy, G. A. (2018). Development of an Onion-Crop Harvester. Misr Journal of Agricultural Engineering, 35(1), 39-56. https://doi.org/10.21608/mjae.2018.96016 DOI: https://doi.org/10.21608/mjae.2018.96016
Pandey, M. M. (2009). Indian agriculture-An introduction. Country report presented in the Fourth Session of the Technical Committee of APCAEM, held during 1-3 December, 2008 at Chiang Rai, Thailand. Available at: https://un-csam.org/sites/default/files/2021-01/in-p.pdf (accessed on 28 November 2025).
Rasool, S., Raheman, H., & Upadhyay, G. (2017). Development of an instrumentation system for evaluating the tractive performance of walking tractors. International Journal of Current Microbiology and Applied Sciences, 6(10), 759-770. https://doi.org/10.20546/ijcmas.2017.610.092 DOI: https://doi.org/10.20546/ijcmas.2017.610.092
Singh, S. (2006). Design, development and field testing of a multipurpose potato digger. Potato Journal, 33(3-4), 134-138.
Singh, S., Singh, R. S., & Singh, S. P. (2014). Farm power availability on Indian farms. Agricultural Engineering Today, 38(4), 44-52.
Srivastava, N. S. L. (1999). Role of Agricultural Engineering in doubling food productions in next ten years. Agricultural Engineering Today, 23(1&2): 37-49.
Srivastava, P., Singh, R., Tripathi, S., & Raghubanshi, A. S. (2016). An urgent need for sustainable thinking in agriculture–An Indian scenario. Ecological Indicators, 67, 611-622. https://doi.org/10.1016/j.ecolind.2016.03.015 DOI: https://doi.org/10.1016/j.ecolind.2016.03.015
Tompkins, F. D., & Bledsoe, B. L. (1979). Vibratory furrow opening tool for minimum tillage planters. Transactions of the ASAE, 22(3), 498-503. https://doi.org/10.13031/2013.35048 DOI: https://doi.org/10.13031/2013.35048
